British Columbia Cost Guides · Prince George
How Much Does Boiler Replacement Cost in Prince George, BC?
Typical cost in Prince George
$8,250
$4,250 low · $14,100 high
All-in replacement price: new boiler, hydronic & gas work, old-unit removal & permit · Updated July 2026
Replacing a boiler in Prince George costs $4,250 to $14,100 installed, and most homeowners pay around $8,250 for a wall-hung gas combi boiler. These are installed replacement prices: the new boiler, hydronic and gas connections, venting, removal and disposal of the old unit, labour, and the permit. A wall-hung combi in a small home sits at the low end. A system boiler feeding an indirect tank in a big radiator house sits at the top, and a handful of premium Vancouver installs are quoted well past it.
Prince George is the one BC city where a boiler failure is a safety problem rather than an inconvenience, and that ought to shape how you buy one. Replacement runs $4,500 to $15,000 on some of the cheapest base labour in the province, but the contractor pool north of Cache Creek is thin and there is very little emergency capacity in January. In-floor slab heat is common here in shops and newer homes, since it suits a climate that stays cold for months. Gas permitting runs through Technical Safety BC at $116 on a contractor permit.
Looking For a Contractor?
Want boiler replacement done at a fair price like the ones on this page? Leave your contacts — we'll pass them to local heating and gas contractors in Prince George, and they'll get back to you with quotes.
Get quotesFree · No obligation
By the PlumbingCosts.ca team — we track published contractor rates, supplier pricing, and permit fees across Canada because you deserve to know a fair price before anyone's in your basement.
Price by Job Type in Prince George
| Job | Low | Average | High |
|---|---|---|---|
| Entry-level combi boiler (84–90%) | $4,250 | $5,150 | $6,100 |
| Mid-range combi boiler (95%+) | $5,150 | $6,750 | $8,450 |
| Premium combi boiler (Viessmann, Lochinvar, Baxi) | $6,600 | $9,850 | $13,150 |
| Conventional heat-only boiler (separate hot water tank) | $6,100 | $8,950 | $12,200 |
| System boiler with an indirect hot water tank | $9,400 | $11,300 | $14,100 |
What's in the Price — and What Isn't
In the price
- The new boiler, sized to the actual heat load rather than to the plate on the old unit
- Draining the system down, disconnecting, and removing and disposing of the old boiler
- Hydronic connections: supply and return, circulator, expansion tank, air separation, and isolation valves
- Gas connection and leak testing
- Venting, plus a condensate drain and neutralizer where a condensing unit needs one
- Refilling, purging air out of every loop, and balancing the zones
- The gas permit, the pressure test, and the inspection sign-off
Costs extra
- Gas line resizing where the supply can't feed a combi at full domestic hot water fire
- Replacing radiators, in-floor manifolds, or zone valves out beyond the boiler room
- A new indirect hot water tank if you're moving from a combi to a system boiler (+$2,500–4,000)
- Chimney work on whatever appliance is left venting into it
- Electrical work for new controls or a dedicated circuit
Boiler quotes hide their differences in the near-boiler piping, not in the box on the wall. Primary and secondary loops, a real air separator, and a low-loss header are what let a modulating boiler actually modulate. A cheap quote is usually a cheap piping job with a good boiler bolted to the front of it.
Calculate Your Estimate
What Moves the Price
- Combi or conventional
- A combi makes heat and domestic hot water in one wall-hung box and lets the old tank go. A system boiler keeps a separate indirect tank, costs $2,500–4,000 more, and is the right answer in a house where two bathrooms can draw at once.
- Venting
- Condensing boilers vent through plastic out a sidewall. Old atmospheric units used the chimney, and once the boiler stops feeding it, whatever else vents up there needs a hard look. Venting changes and condensate routing are the two items that move a boiler quote most often.
- Gas supply sizing
- A combi firing for domestic hot water draws far more gas than the same boiler in heating mode. Undersized supply piping gets found at commissioning, not at the quote, and correcting it usually means opening walls.
- The hydronic side
- Old gravity systems, mixed radiator and in-floor zones, and seized zone valves all add hours. Existing pumps, expansion tanks, and controls rarely make it through a modern boiler swap untouched, and replacing them is labour, not equipment.
- Brand tier
- Entry-level Rheem or Weil-McLain against premium Viessmann or Lochinvar is a $2,500–4,000 spread on equipment alone. What that money buys is turndown range, efficiency at part load, and warranty length.
- Gas permit
- A contractor gas permit for one or two appliances is $116 through Technical Safety BC in 2026, or $164 if a homeowner pulls it — and homeowner permits aren't available for strata or duplex properties, which is where a lot of BC boilers live.
Where a typical $8,250 job goes:
- Materials
- 56% · ~$4,620
- Labour
- 42% · ~$3,465
- Permit & disposal
- 2% · ~$165
How the Job Actually Goes
-
Heat-loss survey and system assessment
The contractor works out the output your radiators or in-floor loops actually need, checks the zones, and decides whether a combi can carry the domestic hot water demand of the house. Most boilers being replaced in BC turn out to be oversized by half.
Included in the quote
-
Drain down and remove the old boiler
The system is isolated and drained, gas and venting come apart, and the old unit is dismantled and carried out. A cast-iron sectional boiler leaves the building in sections, up the stairs, one at a time.
Part of the labour; disposal included on a proper quote
-
Mount and pipe the new boiler
The unit goes on the wall or the pad, then the near-boiler piping gets built: circulator, expansion tank, air separator, isolation valves, and the header feeding the zones. This is the longest and most skilled stretch of the job.
The largest single share of the labour
-
Gas, venting, and condensate
Gas is connected and leak-tested, the sidewall intake and exhaust go in on a condensing unit, and condensate is routed to a drain through a neutralizer where the municipality requires one.
Included; venting changes are the most common add-on
-
Fill, purge, and balance
Loops are refilled, air is purged zone by zone, system pressure is set against the expansion tank, and each zone gets checked for flow. Air left in a hydronic system is why one room in the house stays cold forever.
Included
-
Commission and inspect
The gasfitter runs a combustion analysis, checks gas pressure at full fire, sets the outdoor reset curve, and closes out the permit with Technical Safety BC or the municipal program.
Gas permit $116 contractor or $164 homeowner through TSBC
Do It Yourself or Hire a Pro?
Doing it yourself
- The system can be drained down and the boiler room cleared out ahead of the crew, which is billable time you keep
- Non-gas parts of a hydronic system — thermostats, zone wiring, circulator swaps — are within reach of a competent homeowner once the boiler itself is in and certified
- The gas connection is licensed work, and most BC boilers sit in stratas and duplexes where a homeowner permit isn't available at all
- Commissioning involves combustion analysis, gas pressure measured at full fire, and system pressure and expansion set correctly — none of it optional, all of it instrumented
- A hydronic system holding air or running at the wrong pressure doesn't fail loudly. It heats badly and corrodes quietly for years
- Warranties on modulating condensing boilers are the strictest in the trade, and several manufacturers want both a licensed installer and a commissioning report on file
Hiring a licensed pro
- A licensed gasfitter handles the gas, the venting, and the combustion sign-off
- Near-boiler piping built properly, which is where a modulating boiler's efficiency actually comes from
- The old unit drained, dismantled, and carried out — messier than it sounds on a cast-iron sectional
- Permit pulled, pressure test recorded, warranty registered
- Labour is a bigger share of the bill than on a furnace job, because hydronic work is slow work
- A standard replacement runs four to six hours, but a complicated system takes several days, and the heat is off for them
Our take: There's no DIY version of this job worth attempting. A boiler combines licensed gas work with hydronic system design, and most BC boilers sit in buildings where a homeowner permit isn't even on the table. Put the effort into choosing the contractor instead — the piping around the boiler is where installers separate themselves, and it's the part nobody looks at.
Signs It's Time to Replace
- The boiler is past 20 and its efficiency was in the seventies the day it was installed
- You're bleeding radiators constantly, or one zone never comes up to temperature no matter what the thermostat says
- It short-cycles, firing and shutting down in minutes rather than holding a steady burn
- Corrosion or weeping at the sections, or rust staining on the floor underneath
- Repair parts are getting hard to source, which happens fast once a model goes out of production
- You want the hot water tank gone and the floor space back, which is exactly what a combi buys
How to Keep the Cost Down
- Get quotes on both a combi and a system boiler. In a one- or two-bathroom home the combi is thousands cheaper and takes the hot water tank out of the equation entirely
- Don't buy premium efficiency into a leaky old system. A 98% boiler behind 1950s radiators with no zone control gives back less than the same money spent on controls and insulation
- Ask what the near-boiler piping looks like on each quote. It's the least visible and most consequential difference between a $7,000 job and a $10,500 one
- There's no live FortisBC rebate for a straight gas boiler replacement. The only open gas rebate, up to $3,800, is for households converting from oil or propane to natural gas
- Replace in summer. A boiler that dies in January means an emergency booking on a job that legitimately takes days, not hours
- Decide the domestic hot water plan before you shop. Whether the tank stays or goes changes which boiler you're actually buying
Prince George Notes: Permits, Homes, Rates
Gas permits go through Technical Safety BC ($116 on a contractor permit, 2026); the City of Prince George adds its plumbing permit — a $100 processing fee plus about $78 for a single water-heater fixture.
Local construction puts plenty of mechanical gear in crawlspaces that swing below freezing, which matters twice on a boiler. A condensate line running through unheated space will block, and any part of the hydronic system exposed to that cold wants freeze protection. Vent terminations also have to sit above whatever the snow does by February. None of it is exotic, all of it is local.
Base labour is among the cheapest in BC, but a thin contractor pool inflates emergency and after-hours premiums.
Questions to Ask Before You Hire
- Are you a licensed gasfitter registered with Technical Safety BC, and is the permit inside this price?
- What heat-loss figure did you size this boiler to?
- How are you piping it — primary and secondary with a header, or straight into the existing loop?
- Is removal and disposal of the old boiler included?
- Will I get a commissioning report with the combustion readings on it?
- Where does the new vent terminate, and what happens to the chimney the old boiler was using?
While the Plumber Is There
Call-out time is a big share of any bill — if one of these applies to your home, pricing it in the same visit usually beats a separate appointment.
Hydronic homes have no ductwork, so ductless heads are the usual route to cooling. The rebate on one can be worth more than the boiler costs, which is worth knowing before you commit to gas for another 20 years.
If a combi is on the table, your hot water tank is part of this decision rather than a separate job. Price both before choosing the boiler.
Plenty of BC houses run a boiler for the radiators and a furnace for a later addition. Where they're the same age, doing them together saves a second gas permit and a second crew day.
Common Questions
Boiler Replacement Costs Across British Columbia
| City | Typical range | Average |
|---|---|---|
| Abbotsford | $4,400–$14,700 | $8,600 |
| Burnaby | $4,850–$16,200 | $9,500 |
| Chilliwack | $4,300–$14,400 | $8,450 |
| Coquitlam | $4,750–$15,750 | $9,250 |
| Delta | $4,700–$15,600 | $9,150 |
| Kamloops | $4,300–$14,250 | $8,350 |
| Kelowna | $4,500–$15,000 | $8,800 |
| Langley | $4,600–$15,300 | $9,000 |
| Maple Ridge | $4,600–$15,300 | $9,000 |
| Nanaimo | $4,350–$14,550 | $8,550 |
| New Westminster | $4,750–$15,900 | $9,350 |
| North Vancouver | $5,000–$16,650 | $9,750 |
| Port Coquitlam | $4,700–$15,600 | $9,150 |
| Port Moody | $4,750–$15,750 | $9,250 |
| Prince George (this page) | $4,250–$14,100 | $8,250 |
| Richmond | $4,850–$16,200 | $9,500 |
| Saanich | $4,750–$15,750 | $9,250 |
| Surrey | $4,750–$15,750 | $9,250 |
| Vancouver | $5,050–$16,800 | $9,850 |
| Victoria | $4,750–$15,900 | $9,350 |
| West Vancouver | $5,150–$17,100 | $10,050 |