Skip to content
PlumbingCosts.ca

Updated 2026 Burnaby, BC

How Much Does Dishwasher Installation Cost in Burnaby, BC?

Typical cost in Burnaby

$360

Low $220 High $540

  • Prince George $310
  • Surrey $350
  • Burnaby $360
  • West Vancouver $380

Hookup price into existing water, drain and power: labour and fittings, with the appliance supplied by you.

Installing a dishwasher in Burnaby costs $220 to $540 installed, and most homeowners pay around $360 for a straight swap into a cabinet that already has the connections. Dropping a dishwasher into a cabinet that already has water, drain and power is a short, cheap, well-priced job in British Columbia. Putting one where no dishwasher has ever been is not, and almost nobody in this province publishes a number for it. Below is what the BC market actually quotes, and an honest account of the part it won't quote in advance.

A dishwasher exchange in Burnaby costs $200 to $500 for the hookup, at rates that track Vancouver's closely, and about $50 more to have the old machine gone. Two trades quote this work. Appliance installers price a flat fee, plumbers price a task line, and some flat-rate shops bill a $169 to $189 call-out before either number applies. On a one-hour swap that fee can exceed the install itself, so it belongs in the first phone call rather than on the invoice.

By the PlumbingCosts.ca team — we track published contractor rates, supplier pricing, and permit fees across Canada because you deserve to know a fair price before anyone's in your basement.

Prices

Price by Job Type in Burnaby

Dishwasher Installation prices in Burnaby by job type
Job Low Average High
Hookup only, water, drain and power already there $220 $350 $490
Hookup with the old machine hauled away $270 $400 $540
Call-out fee some flat-rate shops add before the work $169 $179 $189

Scope

What's in the Price — and What Isn't

In the price

  • Sliding the old machine out, disconnecting it, and taking it away where the quote says so
  • Water supply connected to the hot side, usually off a stop under the sink
  • Drain hose run to the sink tailpiece or the garburator inlet, with a high loop or air gap
  • Plugging in or wiring to the existing connection point in the cabinet
  • Levelling the machine in the opening, securing it to the counter or cabinet sides, and running a cycle to check for weeping at the fittings

Costs extra

  • The dishwasher itself — every published BC price above assumes you supplied it
  • A new hot-water line, drain tie-in or receptacle where none exists
  • Cabinet modification for an opening that isn't standard width or height
  • Counter or flooring repair where the old machine has been leaking
  • Replacing a corroded angle stop under the sink that won't shut off cleanly

The materials share on this job is tiny, and that's not an error. A stainless supply hose, elbow and cord kit is about $16 at Amazon.ca, so almost everything you're paying for is the hour and the trade. That's also why the flat fee barely moves between a $600 machine and a $2,400 one.

Drain hose fastened high under the counter Drain tie-in at the tailpiece or garburator Receptacle inside the cabinet run Hot supply off the stop under the sink 24 in. opening All three already there: $200–450. Any of them missing: quoted on site.
Water, drain and power are the three things a dishwasher needs, and every published BC price assumes all three are already in the cabinet. The high loop costs nothing at install time and is what stops sink water running back into the machine.

Calculator

Calculate Your Estimate

Anything that applies:

Estimated cost in Burnaby

Low

$220

basic swap

Typical

$350

most homes

High

$490

complex job

$220Most pay $350$490
Materials
$10 – $20
Labour
$180 – $400
Permit & disposal
$30 – $60

Estimates a hookup price for your city, assuming the water, drain and power are already in the cabinet. Not a quote.

Cost drivers

What Moves the Price

Whether the three services are already there
A dishwasher needs hot water, a drain tie-in and a receptacle inside the cabinet run. Where all three exist, BC installers quote $200 to $409 and the work takes an hour or two. Where any of them has to be run, no BC company we found publishes a rate, and it becomes an on-site quote.
Who's doing it
Two trades price this job. Appliance installers quote a flat fee, one Lower Mainland firm publishing $245 with a further $50 to take the old machine away. Plumbers price it as a task line, with one North Vancouver price list at $409 to fit a homeowner-supplied unit. A general contractor pricing the same work at $200 to $400 notes it may take a plumber and an electrician between them.
The old machine
Removal and disposal is small, itemized and worth asking about. One BC installer charges $50 flat to take the old dishwasher; others fold it in. Nobody charges hundreds, so treat a vague "disposal" line as negotiable.
The drain connection
The hose has to reach a tie-in on the sink drain or the garburator, with a high loop or an air gap so waste water can't siphon back into the tub. Where the run is long or the cabinet is on the far side of the sink, the drain is the part that adds time.
Electrical
Some dishwashers arrive with a cord and some are meant to be hard-wired to a junction box. A cabinet with no receptacle means an electrician, on their own line of the bill rather than as a plumbing extra.
The cabinet opening
Standard is 24 inches wide by roughly 34 inches high. Older BC kitchens, especially in pre-1980 houses and walk-up apartments, often have an opening that was cut for a different appliance, and the fix is cabinetry work rather than plumbing.

Where a typical $360 job goes:

Materials
5% · ~$18
Labour
82% · ~$295
Permit & disposal
13% · ~$47

On the day

How the Job Actually Goes

  1. Checking what the cabinet already has

    Hot-water stop under the sink, a drain tie-in with a spare port or a garburator inlet, and a receptacle or junction box inside the run. All three present means a flat-rate job. Any one missing changes the trade and the number.

    Included, or a $169–189 attendance charge at flat-rate shops

  2. Old machine out

    Power off at the breaker, water off at the stop, drain hose released, and the counter screws backed out before anything gets pulled. The floor gets protected first, because there is always more water left in the sump than expected.

    $50 flat for removal and disposal at one BC installer

  3. Water and drain

    Supply elbow into the inlet valve by hand first, then a quarter turn with a wrench. Drain hose routed with a high loop fastened up under the counter, or to an air gap where one is fitted, so sink water can't back-feed the tub.

    Fittings are pennies; this is where the labour goes

  4. Power

    Cord into the existing receptacle, or wired into the junction box if the machine came without one. Not a plumber's line item, and worth confirming who is doing it before the day.

    Included if a receptacle exists; an electrician's call if not

  5. Level, secure, run a cycle

    Feet adjusted so the door closes square and the tub drains fully, brackets screwed to the counter or the cabinet sides, then a full cycle with a torch on the fittings and a hand under the machine at the end.

    Included

DIY

Do It Yourself or Hire a Pro?

Doing it yourself

  • On a straight swap the whole job is four connections: water, drain, power, and two screws into the underside of the counter
  • The hardware kit is genuinely cheap, roughly $16 for hoses, elbow and cord, against $200 to $409 for the labour
  • Nothing about exchanging an appliance on existing services is permitted work in BC
  • The 90-degree elbow at the water inlet is the classic failure: cross-thread it or over-tighten it into the plastic valve body and a slow drip starts under a machine nobody ever looks under
  • Skip the high loop and the sink drains back into the dishwasher, which reads as a broken appliance and isn't
  • A new machine's drain hose is often shorter than the old one, and splicing an extension in the wrong place is where kitchen floods start
  • Manoeuvring a 40 kg appliance out of a tight opening tends to score vinyl and hardwood on the way

Hiring a licensed pro

  • Fittings torqued properly and the cycle watched under real water pressure before anyone leaves
  • The condition of the shut-off valve gets judged while the water is already off
  • Old machine gone for $50 or less as an itemized line
  • If the drain, the stop or the receptacle turns out to be wrong, you find out from someone who can fix it that day
  • A call-out fee of $169 to $189 at some shops can exceed the install line itself
  • Two trades may be involved when the cabinet has no receptacle, which means two schedules

Our take: If your kitchen has a working dishwasher today, replacing it is a reasonable DIY afternoon, and the high loop plus a careful inlet elbow are 90% of doing it right. Bring someone in when there has never been a dishwasher in that cabinet, when the shut-off under the sink is seized, or when the machine has to be hard-wired. Those are the versions BC contractors will only quote after standing in your kitchen, which is a fair signal that they're not routine.

Signs It's Time to Replace

  • Water under the machine or a swollen cabinet base, which is a fitting or a tub seam rather than a cycle problem
  • Dishes coming out gritty on a machine that has had its filter cleaned and its spray arms cleared
  • Standing water in the tub between cycles, often a drain hose without a high loop rather than a failed pump
  • A drain hose spliced with tape, or a supply line that's a garden-hose fitting on a compression stop
  • The machine is 10 years old and the door hinges or the latch have gone, which is usually the point where repair stops paying
  • No dishwasher in a kitchen that has cabinet space for one, where this becomes a first install and not a swap

How to Keep the Cost Down

  1. Buy the appliance yourself. Every published BC price for this work assumes a homeowner-supplied machine, so the delivery fee from the retailer is the only alternative worth comparing
  2. Ask the retailer what their delivery-and-install package covers before booking a trade separately. Some cover a straight swap, none cover running new services
  3. Line up the electrical question before the day. A plumber who arrives to find no receptacle in the cabinet still bills the visit
  4. Have the old machine out and the space clear if you're comfortable doing that much. Taking the old machine away is a $50 line, and it's the easiest one to strike
  5. Book it alongside another kitchen job. The trip charge lands once, no matter how many fittings get touched

Local

Burnaby Notes: Permits, Homes, Rates

Burnaby operates its own gas permit program, one of the few BC municipalities that does. Its gas permit is $70 for the first appliance ($39 each additional), with the city's plumbing permit at $121 for the first fixture.

Metrotown, Brentwood and Lougheed put a large share of Burnaby households in a tower suite, where the job starts with finding the in-suite shut-off under the sink. Many stratas want a licensed installer and proof of insurance for anything connected to a water line, and some ask for a pan under the machine, so read your bylaws before booking. The 1950s and 60s houses on the south slope are the ones with kitchens never laid out for a dishwasher, which is plumber work plus a $121 first-fixture permit.

Rates track close to Vancouver.

Hiring

Questions to Ask Before You Hire

  1. Is this a flat fee, and is there a separate call-out charge on top of it?

  2. Does the price assume the water, drain and receptacle are already in the cabinet?

  3. If the shut-off under the sink won't close, where does the number go?

  4. Do you take the old machine away, and what does that cost?

  5. Are you fitting a high loop or an air gap, and which one does my setup need?

  6. If it needs an electrician, are you bringing one or am I booking that separately?

Same visit

While the Plumber Is There

Call-out time is a big share of any bill — if one of these applies to your home, pricing it in the same visit usually beats a separate appointment.

Garburator Installation

The dishwasher drain usually ties into the garburator's inlet port, so both units live on the same fitting. If the garburator is on its way out, doing them together saves opening the same cabinet twice.

Drain Cleaning

A dishwasher that drains slowly is often a kitchen branch line greased up further downstream. Worth knowing before you blame a new machine for something the pipe is doing.

Leak Detection

Cabinet bases swell from slow drips long before anything shows on the floor. If the old machine has been weeping, find out how far it went before you slide a new one into the same spot.

FAQ

Common Questions

Burnaby operates its own gas permit program, one of the few BC municipalities that does. Its gas permit is $70 for the first appliance ($39 each additional), with the city's plumbing permit at $121 for the first fixture.

Compare

Dishwasher Installation Costs Across British Columbia

Dishwasher Installation cost comparison across BC cities
City Typical range
Abbotsford $200–$490
Burnaby (this page) $220–$540
Chilliwack $190–$480
Coquitlam $210–$530
Delta $210–$520
Kamloops $190–$480
Kelowna $200–$500
Langley $200–$510
Maple Ridge $200–$510
Nanaimo $190–$490
New Westminster $210–$530
North Vancouver $220–$560
Port Coquitlam $210–$520
Port Moody $210–$530
Prince George $190–$470
Richmond $220–$540
Saanich $210–$530
Surrey $210–$530
Vancouver $220–$560
Victoria $210–$530
West Vancouver $230–$570